- Codice RS:
- 130-6124
- Codice costruttore:
- ATATMEL-ICE-PCBA
- Costruttore:
- Microchip
1 In consegna il giorno lavorativo successivo per ordini pervenuti entro le 19:00 (magazzino in Italia)
2 Entro 1 giorni lavorativi per ordini effettuati entro le 19:00 (magazzini in Europa)
Prezzo per Unità
93,37 €
(IVA esclusa)
113,91 €
(IVA inclusa)
Unità | Per unità |
1 + | 93,37 € |
- Codice RS:
- 130-6124
- Codice costruttore:
- ATATMEL-ICE-PCBA
- Costruttore:
- Microchip
Documentazione Tecnica
Normative
Dettagli prodotto
ATATMEL-ICE PCBA
The Atmel-ICE series consists of development tools for debugging and programming ARM Cortex-M based Atmel SAM and Atmel AVR microcontrollers with on-chip debug capability. The Atmel-ICE series supports JTAG, SWD, PDI, TPI, aWire, SPI and debugWIRE interfaces and is compatible with Atmel Studio.
Kit Contains:
Atmel-ICE unit without plastic encapsulation
130-6122 Full Kit available
130-6123 Basic Kit available
System Requirements
The Atmel-ICE unit requires that a front-end debugging environment Atmel Studio version 6.2 or later is installed on your computer. The Atmel-ICE should be connected to the host computer using the USB cable provided, or a certified Micro-USB cable.
How to turn the Atmel - ICE on?
The Atmel-ICE is powered by the USB bus voltage. It requires less than 100mA to operate, and can, therefore, be powered through a USB hub. The power LED will illuminate when the unit is plugged in. When not connected in an active programming or debugging session, the unit will enter low-power consumption mode to preserve your computer's battery. The Atmel-ICE cannot be powered down - it should be unplugged when not in use.
How does it connect?
The Atmel-ICE communicates primarily using a standard HID interface and does not require a special driver on the host computer. The Atmel-ICE must be connected to an available USB port on the host computer using the USB cable provided, or suitable USB certified micro cable. The Atmel-ICE contains a USB 2.0 compliant controller and can operate in both full-speed and high-speed modes. For best results, connect the Atmel-ICE directly to a USB 2.0 compliant high-speed hub on the host computer using the cable provided.
The Atmel-ICE is powered by the USB bus voltage. It requires less than 100mA to operate, and can, therefore, be powered through a USB hub. The power LED will illuminate when the unit is plugged in. When not connected in an active programming or debugging session, the unit will enter low-power consumption mode to preserve your computer's battery. The Atmel-ICE cannot be powered down - it should be unplugged when not in use.
How does it connect?
The Atmel-ICE communicates primarily using a standard HID interface and does not require a special driver on the host computer. The Atmel-ICE must be connected to an available USB port on the host computer using the USB cable provided, or suitable USB certified micro cable. The Atmel-ICE contains a USB 2.0 compliant controller and can operate in both full-speed and high-speed modes. For best results, connect the Atmel-ICE directly to a USB 2.0 compliant high-speed hub on the host computer using the cable provided.
Tipo di kit
Specifiche
Attributo | Valore |
---|---|
Accessori | Kit di sviluppo |
Utilizzabile con | Microcontrollori SAM, AVR |
Interfaccia | JTAG, SWD, PDI, TPI, aWire, SPI, debugWIRE, UPDI |
Nome del programmatore | Atmel-ICE |
Link consigliati
- Kit di programmazione Atmel-ICE Microchip, interfaccia JTAG
- Ventola di raffreddamento per torre ICE per Raspberry Pi 52Pi
- Accessori per kit di sviluppo Microchip ATATMEL-ICE-ADPT, Atmel-ICE
- Adattatore di programmazione chip AC102015 per Atmel-ICE connettori Power
- Programmatore J-Link ARM JTAG Isolator Board SEGGER
- Accessori per kit di sviluppo Microchip ATATMEL-ICE-CABLE, Atmel-ICE
- Ice Diamond Deep Freeze Coldstore Jacket
- Ice Diamond Deep Freeze Coldstore Trouse